Audio manuals and audio service pdf instructions. Find the user manual you need for your audio device and more at ManualsOnline.
. Pass Output.5 Power Light.5 For your Jensen amplifier to work right, it must be Protect Light.5 installed correctly. This manual will show you how to Input Level Control.6 install your new amplifier like a pro. ® XA2150 Features The Jensen XA2150 power amplifier is a two-. 150 watts RMS bridged into a 4 ohm load channel 300-watt total system power automotive.
Bridgeable design to direct full power to one amplifier. The XA2150 includes: speaker. ® XA2150 Supplies and Tools Needed Routing Wires Supplies:.
Speaker wire (12 gauge for subwoofers, 16-18 Battery gauge for other speakers) Battery. Sheet metal type screws for mounting amplifier Connector. Electrical tape. Solderless crimp connectors Fuse or. ® XA2150 Wiring Power and Outputs + 12V FUSE L – R – POWER SPEAKER Power Terminal (BATT +12V) Remote Terminal (RMT +12V) Connect the radio power antenna lead from Connect directly to the vehicle battery+ the receiver to the amplifier REMOTE terminal. ® XA2150 Inputs and Controls HIGH INPUT LOW INPUT PASS OUTPUT POWER PROTECT Input Wiring Pass Output Inputs may be high level (from the receiver's PASS OUTPUT speaker) or low level (from special low level Use pass through (PASS outputs).
Low level input is preferred for best OUTPUT) connectors for performance. Use with 6' or smaller X-OVER speakers. FULL Use LPF and HPF to adjust from 50 to 250Hz. When using your Jensen amplifier to run a subwoofer and two full- Input Level Control range speakers (known as Tri- mode or three channel operation) LEVEL. ® XA2150 Speaker Wiring 2 Speakers 2 Subwoofers RCA Cables RCA Cables L – R – L – R – X-OVER X-OVER FULL FULL. ® XA2150 2 Speakers + Subwoofer Bridged Subwoofer RCA Cables RCA Cables L – R – L – R – High Pass Filters X-OVER minimum FULL Low Pass X-OVER Filter (available at most car stereo installation stores) FULL Important When running a subwoofer and two full-range speakers together (Tri-mode operation), high and low pass filters must be used. ® XA2150 Testing Before you finish the installation, you should do the following tests to make sure the wiring is correct and everything is operating properly.
Reconnect Battery Professional Tip Dealing with Alternator Noise When wiring is complete, reconnect the battery The vehicle alternator can cause a “siren”. ® XA2150 Professional Tip Professional Tip Securing Wires Installing in Trunk When installing the amplifier in the trunk, run Be proud of your installation! Use wire ties to the power wires along the same path as the bundle wires together when possible. (But other vehicle wiring. Amp will not operate into 2 ohms bridged No output on channels Speaker wires not connected to Refer to pages 5, 6 and 7 for proper installation speakers properly Input hooked up incorrectly Can’t find cause of problem Contact Jensen Technical Assistance (1-800-323-0221). Jensen will pay the return shipping charges if the product is What is Covered.
Except as otherwise specified below, returned to an address inside the USA or Canada.
User Manual JENSEN JR300C - This User Manual - also called owner's manual or operating instructions - contains all information for the user to make full use of the product. This manual includes a description of the functions and capabilities and presents instructions as step-by-step procedures. Error codes and the Reference manual can also be included. This document contains important information to use and/or repair your appliance. Depending on the nature of the manual (use, installation, service, parts list), it provides instructions that you can't ignore. We provide PDF manuals: easy to download, the documents can be displayed on any equipment like mobile, tablet and computer. This is an official document edited by the manufacturer or a local distributor.
Enter your email: Download Electronic file ready for instant download (US$ 10.90).